add tlp config

2026-02-06 19:45:16 +02:00
parent 9addd3d2f9
commit 57824c6ff3
1 changed files with 631 additions and 0 deletions
--- a/etc/tlp.conf
+++ b/etc/tlp.conf
@@ -0,0 +1,631 @@
+# ----------------------------------------------------------------------------
+# /etc/tlp.conf - TLP user configuration (version 1.9.0)
+# See full explanation: https://linrunner.de/tlp/settings
+#
+# Copyright (c) 2025 Thomas Koch <linrunner at gmx.net> and others.
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Settings are read in the following order:
+#
+# 1. Intrinsic defaults
+# 2. /etc/tlp.d/*.conf - Drop-in customization snippets
+# 3. /etc/tlp.conf     - User configuration (this file)
+#
+# Power Profiles: a part of TLP's parameters is divided into two or three
+# groups:
+# - performance: parameters ending in _AC are used when AC power is
+#   connected or when the command 'tlp performance' is run.
+# - balanced: parameters ending in _BAT are used when operating
+#   on battery power or when the command 'tlp balanced' is run.
+# - power-saver: parameters ending in _SAV are used when the command
+#   'tlp power-saver' is run. If there is no _SAV parameter available
+#   for a feature, the _BAT parameter will be used instead.
+# - Any remaining parameters not divided apply to all power profiles.
+#
+# Please note:
+# - If parameters are specified more than once, the last occurrence takes
+#   precedence. This also means that any parameters defined here will take
+#   precedence over any drop-ins.
+# - You can however, append values to a parameter already defined as intrinsic
+#   default or in a previously read file: use PARAMETER+="add values".
+# - Important: all parameters are disabled here. Remove the leading '#' if you
+#   want to enable a feature without a default or if you want to set a value
+#   other than the default.
+# - Parameters must always be specified for all power profiles, i.e. in the
+#   AC, BAT and SAV category (where applicable). If you omit one of them,
+#   the missing profile will receive its value from another profile, since
+#   a change will only occur if different values are defined.
+# - To completely disable a parameter, use PARAMETER="".
+# Legend for defaults:
+# - Default *: intrinsic default that is effective when the parameter is
+#   missing or the line has a leading #'.
+# - Default <none>: do nothing or use kernel/hardware defaults.
+#
+# ----------------------------------------------------------------------------
+# tlp - Parameters for power saving
+
+# Set to 0 to disable, 1 to enable TLP.
+# Default: 1
+
+#TLP_ENABLE=1
+
+# Set to 1 to deactivate all intrinsic defaults of TLP. This means that
+# TLP only applies settings that have been explicitly activated i.e.
+# parameters without a leading '#'.
+# Notes:
+# - Helpful if one wants to use only selected features of TLP
+# - After activation, use tlp-stat -c to display your effective configuration
+
+#TLP_DISABLE_DEFAULTS=1
+
+# Control how warnings about invalid settings are issued:
+#   0=disabled
+#   1=background tasks (boot, resume, change of power source) report to syslog
+#   2=shell commands report to the terminal (stderr)
+#   3=combination of 1 and 2
+# Default: 3
+
+#TLP_WARN_LEVEL=3
+
+# Colorize error, warning, notice and success messages. Colors are specified
+# with ANSI codes:
+#   1=bold black, 90=grey, 91=red, 92=green, 93=yellow, 94=blue, 95=magenta,
+#   96=cyan, 97=white.
+# Other colors are possible, refer to:
+#   https://en.wikipedia.org/wiki/ANSI_escape_code#3-bit_and_4-bit
+# Colors must be specified in the order
+#   "<error> <warning> <notice> <success>".
+# By default, errors are shown in red, warnings in yellow, notices in bold
+# and success in green.
+# Default: "91 93 1 92"
+
+#TLP_MSG_COLORS="91 93 1 92"
+
+# Control automatic switching of the power profile when connecting or removing
+# the charger, when booting the system or when executing 'tlp start':
+#   0=disabled - never switch, use TLP_DEFAULT_MODE if configured
+#   1=auto  - always switch, select performance on AC and
+#             balanced on battery power.
+#   2=smart - do not switch if the following profiles were active previously:
+#             power-saver or balanced on AC resp.
+#             power-saver or performance on battery power.
+# Note: the same applies if the charger was connected/removed during suspend.
+# Default: 2
+
+TLP_AUTO_SWITCH=0
+
+# Power profile to use when automatic switching is disabled
+# (TLP_AUTO_SWITCH=0), profile is locked (TLP_PERSISTENT_DEFAULT=1)
+# or no power supply is detected:
+#   PRF=performance, BAL=balanced, SAV=power-saver.
+# Note: legacy values AC and BAT continue to work. They are mapped to
+# PRF and BAL, respectively.
+# Default: <none>
+
+#TLP_DEFAULT_MODE=BAL
+
+# Lock power profile:
+#   0=profile depends on automatic switching,
+#   1=profile is locked to TLP_DEFAULT_MODE (TLP_AUTO_SWITCH is ignored).
+# Default: 0
+
+#TLP_PERSISTENT_DEFAULT=0
+
+# Power supply classes to ignore when determining power profile:
+#  AC, USB, BAT.
+# Separate multiple classes with spaces.
+# Note: try on laptops where operation mode AC/BAT is incorrectly detected.
+# Default: <none>
+
+#TLP_PS_IGNORE="BAT"
+
+# Seconds laptop mode has to wait after the disk goes idle before doing a
+# sync. Non-zero value enables, zero disables laptop mode.
+# Default: 0 (AC), 2 (BAT)
+
+#DISK_IDLE_SECS_ON_AC=0
+#DISK_IDLE_SECS_ON_BAT=2
+
+# Dirty page values (timeouts in secs).
+# Default: 15 (AC), 60 (BAT)
+
+#MAX_LOST_WORK_SECS_ON_AC=15
+#MAX_LOST_WORK_SECS_ON_BAT=60
+
+# Select a CPU scaling driver operation mode.
+# Intel CPU with intel_pstate driver:
+#   active, passive.
+# AMD Zen 2 or newer CPU with amd-pstate driver as of kernel 6.3/6.4(*):
+#   active, passive, guided(*).
+# Default: <none>
+#CPU_DRIVER_OPMODE_ON_AC=active
+#CPU_DRIVER_OPMODE_ON_BAT=active
+#CPU_DRIVER_OPMODE_ON_SAV=active
+
+# Select a CPU frequency scaling governor.
+# Intel CPU with intel_pstate driver or
+# AMD CPU with amd-pstate driver in active mode ('amd-pstate-epp'):
+#   performance, powersave(*).
+# Intel CPU with intel_pstate driver in passive mode ('intel_cpufreq') or
+# AMD CPU with amd-pstate driver in passive or guided mode ('amd-pstate') or
+# Intel, AMD and other CPU brands with acpi-cpufreq driver:
+#   conservative, ondemand(*), userspace, powersave, performance, schedutil(*)
+# Use tlp-stat -p to show the active driver and available governors.
+# Important:
+#   Governors marked (*) above are power efficient for *almost all* workloads
+#   and therefore kernel and most distributions have chosen them as defaults.
+#   You should have done your research about advantages/disadvantages *before*
+#   changing the governor.
+# Default: <none>
+
+CPU_SCALING_GOVERNOR_ON_AC=performance
+CPU_SCALING_GOVERNOR_ON_BAT=powersave
+CPU_SCALING_GOVERNOR_ON_SAV=powersave
+
+# Set the min/max frequency available for the scaling governor.
+# Possible values depend on your CPU. For available frequencies see
+# the output of tlp-stat -p.
+# Notes:
+# - Min/max frequencies must always be specified for both AC *and* BAT
+# - Not recommended for use with the intel_pstate driver, use
+#   CPU_MIN/MAX_PERF_ON_AC/BAT below instead
+# Default: <none>
+
+#CPU_SCALING_MIN_FREQ_ON_AC=0
+#CPU_SCALING_MAX_FREQ_ON_AC=0
+#CPU_SCALING_MIN_FREQ_ON_BAT=0
+#CPU_SCALING_MAX_FREQ_ON_BAT=0
+#CPU_SCALING_MIN_FREQ_ON_SAV=0
+#CPU_SCALING_MAX_FREQ_ON_SAV=0
+
+# Set CPU energy/performance policies EPP and EPB:
+#   performance, balance_performance, default, balance_power, power.
+# Values are given in order of increasing power saving.
+# Requires:
+# * Intel CPU
+#   EPP: Intel Core i 6th gen. or newer CPU with intel_pstate driver
+#   EPB: Intel Core i 2nd gen. or newer CPU with intel_pstate driver
+#   EPP and EPB are mutually exclusive: when EPP is available, Intel CPUs
+#   will not honor EPB. Only the matching feature will be applied by TLP.
+# * AMD Zen 2 or newer CPU
+#   EPP: amd-pstate driver in active mode ('amd-pstate-epp') as of kernel 6.3
+# Default: balance_performance (AC), balance_power (BAT), power (SAV)
+
+CPU_ENERGY_PERF_POLICY_ON_AC=performance
+CPU_ENERGY_PERF_POLICY_ON_BAT=balance_power
+CPU_ENERGY_PERF_POLICY_ON_SAV=power
+
+# Set Intel CPU P-state performance: 0..100 (%).
+# Limit the max/min P-state to control the power dissipation of the CPU.
+# Values are stated as a percentage of the available performance.
+# Requires Intel Core i 2nd gen. or newer CPU with intel_pstate driver.
+# Default: <none>
+
+#CPU_MIN_PERF_ON_AC=0
+#CPU_MAX_PERF_ON_AC=100
+#CPU_MIN_PERF_ON_BAT=0
+#CPU_MAX_PERF_ON_BAT=80
+#CPU_MIN_PERF_ON_SAV=0
+#CPU_MAX_PERF_ON_SAV=60
+
+# Set the CPU "turbo boost" (Intel) or "core performance boost" (AMD) feature:
+#   0=disable, 1=allow.
+# Allows to raise the maximum frequency/P-state of some cores if the
+# CPU chip is not fully utilized and below it's intended thermal budget.
+# Note: a value of 1 does *not* activate boosting, it just allows it.
+# Default: <none>
+
+CPU_BOOST_ON_AC=1
+CPU_BOOST_ON_BAT=1
+CPU_BOOST_ON_SAV=0
+
+# Set CPU dynamic boost feature:
+#   0=disable, 1=enable.
+# Improve performance by increasing minimum P-state limit dynamically
+# whenever a task previously waiting on I/O is selected to run.
+# Requires Intel Core i  6th gen. or newer CPU with intel_pstate driver
+# in active mode.
+# Note: AMD CPUs currently have no tunable for this.
+# Default: <none>
+
+#CPU_HWP_DYN_BOOST_ON_AC=1
+#CPU_HWP_DYN_BOOST_ON_BAT=1
+#CPU_HWP_DYN_BOOST_ON_SAV=0
+
+# Kernel NMI Watchdog:
+#   0=disable (default, saves power), 1=enable (for kernel debugging only).
+# Default: 0
+
+#NMI_WATCHDOG=0
+
+# Select platform profile:
+#   performance, balanced, low-power.
+# Controls system operating characteristics around power/performance levels,
+# thermal and fan speed. Values are given in order of increasing power saving.
+# Note: check the output of tlp-stat -p to determine availability on your
+# hardware and additional profiles such as: balanced-performance, quiet, cool.
+# Default: performance (AC), balanced (BAT), low-power (SAV)
+
+PLATFORM_PROFILE_ON_AC=performance
+PLATFORM_PROFILE_ON_BAT=balanced
+PLATFORM_PROFILE_ON_SAV=low-power
+
+# System suspend mode:
+#   s2idle: Idle standby - a pure software, light-weight, system sleep state,
+#   deep: Suspend to RAM - the whole system is put into a low-power state,
+#     except for memory, usually resulting in higher savings than s2idle.
+# CAUTION: changing suspend mode may lead to system instability and even
+# data loss. As for the availability of different modes on your system,
+# check the output of tlp-stat -s. If unsure, stick with the system default
+# by not enabling this.
+# Default: <none>
+
+#MEM_SLEEP_ON_AC=s2idle
+#MEM_SLEEP_ON_BAT=deep
+
+# Define disk devices on which the following DISK/AHCI_RUNTIME parameters act.
+# Separate multiple devices with spaces.
+# Devices can be specified by disk ID also (lookup with: tlp diskid).
+# Default: "nvme0n1 sda"
+
+#DISK_DEVICES="nvme0n1 sda"
+
+# Disk advanced power management level: 1..254, 255 (max saving, min, off).
+# Levels 1..127 may spin down the disk; 255 allowable on most drives.
+# Separate values for multiple disks with spaces. Use the special value 'keep'
+# to keep the hardware default for the particular disk.
+# Default: 254 (AC), 128 (BAT)
+
+#DISK_APM_LEVEL_ON_AC="254 254"
+#DISK_APM_LEVEL_ON_BAT="128 128"
+
+# Exclude disk classes from advanced power management (APM):
+#   sata, ata, usb, ieee1394.
+# Separate multiple classes with spaces.
+# CAUTION: USB and IEEE1394 disks may fail to mount or data may get corrupted
+# with APM enabled. Be careful and make sure you have backups of all affected
+# media before removing 'usb' or 'ieee1394' from the denylist!
+# Default: "usb ieee1394"
+
+#DISK_APM_CLASS_DENYLIST="usb ieee1394"
+
+# Hard disk spin down timeout:
+#   0:        spin down disabled
+#   1..240:   timeouts from 5s to 20min (in units of 5s)
+#   241..251: timeouts from 30min to 5.5 hours (in units of 30min)
+# See 'man hdparm' for details.
+# Separate values for multiple disks with spaces. Use the special value 'keep'
+# to keep the hardware default for the particular disk.
+# Default: <none>
+
+#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
+#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"
+
+# Select I/O scheduler for the disk devices.
+# Multi queue (blk-mq) schedulers:
+#   mq-deadline(*), none, kyber, bfq
+# Single queue schedulers:
+#   deadline(*), cfq, bfq, noop
+# (*) recommended.
+# Separate values for multiple disks with spaces. Use the special value 'keep'
+# to keep the kernel default scheduler for the particular disk.
+# Notes:
+# - Multi queue (blk-mq) may need kernel boot option 'scsi_mod.use_blk_mq=1'
+#   and 'modprobe mq-deadline-iosched|kyber|bfq' on kernels < 5.0
+# - Single queue schedulers are legacy now and were removed together with
+#   the old block layer in kernel 5.0
+# Default: keep
+
+#DISK_IOSCHED="mq-deadline mq-deadline"
+
+# AHCI link power management (ALPM) for SATA disks:
+#   min_power, med_power_with_dipm(*), medium_power, max_performance.
+# (*) recommended.
+# Multiple values separated with spaces are tried sequentially until success.
+# Default: med_power_with_dipm (AC & BAT)
+
+#SATA_LINKPWR_ON_AC="med_power_with_dipm"
+#SATA_LINKPWR_ON_BAT="med_power_with_dipm"
+
+# Exclude SATA links from AHCI link power management (ALPM).
+# SATA links are specified by their host. Refer to the output of
+# tlp-stat -d to determine the host; the format is "hostX".
+# Separate multiple hosts with spaces.
+# Default: <none>
+
+#SATA_LINKPWR_DENYLIST="host1"
+
+# Runtime Power Management for NVMe, SATA, ATA and USB disks
+# as well as SATA ports:
+#   on=disable, auto=enable.
+# Note: SATA controllers are PCIe bus devices and handled by RUNTIME_PM
+# further down.
+
+# Default: on (AC), auto (BAT)
+
+#AHCI_RUNTIME_PM_ON_AC=on
+#AHCI_RUNTIME_PM_ON_BAT=auto
+
+# Seconds of inactivity before disk is suspended.
+# Note: effective only when AHCI_RUNTIME_PM_ON_AC/BAT is activated.
+# Default: 15
+
+#AHCI_RUNTIME_PM_TIMEOUT=15
+
+# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
+# Drive can be powered on again by releasing (and reinserting) the eject lever
+# or by pressing the disc eject button on newer models.
+# Note: an UltraBay/MediaBay hard disk is never powered off.
+# Default: 0
+
+#BAY_POWEROFF_ON_AC=0
+#BAY_POWEROFF_ON_BAT=0
+
+# Optical drive device to power off
+# Default: sr0
+
+#BAY_DEVICE="sr0"
+
+# Set the min/max/turbo frequency for the Intel GPU.
+# Possible values depend on your hardware. For available frequencies see
+# the output of tlp-stat -g.
+# Default: <none>
+
+#INTEL_GPU_MIN_FREQ_ON_AC=0
+#INTEL_GPU_MIN_FREQ_ON_BAT=0
+#INTEL_GPU_MAX_FREQ_ON_AC=0
+#INTEL_GPU_MAX_FREQ_ON_BAT=0
+#INTEL_GPU_BOOST_FREQ_ON_AC=0
+#INTEL_GPU_BOOST_FREQ_ON_BAT=0
+
+# AMD GPU power management.
+# Performance level (DPM): auto, low, high; auto is recommended.
+# Note: requires amdgpu or radeon driver.
+# Default: auto
+
+#RADEON_DPM_PERF_LEVEL_ON_AC=auto
+#RADEON_DPM_PERF_LEVEL_ON_BAT=auto
+
+# Dynamic power management method (DPM): balanced, battery, performance.
+# Note: radeon driver only.
+# Default: <none>
+
+#RADEON_DPM_STATE_ON_AC=performance
+#RADEON_DPM_STATE_ON_BAT=battery
+
+# Display panel adaptive backlight modulation (ABM) level: 0(off), 1..4.
+# Values 1..4 control the maximum brightness reduction allowed by the ABM
+# algorithm, where 1 represents the least and 4 the most power saving.
+# Notes:
+# - Requires AMD Vega or newer GPU with amdgpu driver as of kernel 6.9
+# - Savings are made at the expense of color balance
+# Default: 0 (AC), 1 (BAT), 3 (SAV)
+
+#AMDGPU_ABM_LEVEL_ON_AC=0
+#AMDGPU_ABM_LEVEL_ON_BAT=1
+#AMDGPU_ABM_LEVEL_ON_SAV=3
+
+# Wi-Fi power saving mode: on=enable, off=disable.
+# Default: off (AC), on (BAT)
+
+WIFI_PWR_ON_AC=off
+WIFI_PWR_ON_BAT=off
+
+# Disable Wake-on-LAN: Y/N.
+# Default: Y
+
+WOL_DISABLE=Y
+
+# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
+# A value of 0 disables, >= 1 enables power saving.
+# Note: 1 is recommended for Linux desktop environments with PulseAudio,
+# systems without PulseAudio may require 10.
+# Default: 1
+
+#SOUND_POWER_SAVE_ON_AC=1
+#SOUND_POWER_SAVE_ON_BAT=1
+
+# Disable controller too (HDA only): Y/N.
+# Note: effective only when SOUND_POWER_SAVE_ON_AC/BAT is activated.
+# Default: Y
+
+#SOUND_POWER_SAVE_CONTROLLER=Y
+
+# PCIe Active State Power Management (ASPM):
+#   default(*), performance, powersave, powersupersave.
+# (*) keeps BIOS ASPM defaults (recommended)
+# Default: <none>
+
+#PCIE_ASPM_ON_AC=default
+#PCIE_ASPM_ON_BAT=default
+
+# Runtime Power Management for PCIe bus devices: on=disable, auto=enable.
+# Default: on (AC), auto (BAT)
+
+#RUNTIME_PM_ON_AC=on
+#RUNTIME_PM_ON_BAT=auto
+
+# Exclude listed PCIe device adresses from Runtime PM.
+# Note: this preserves the kernel driver default, to force a certain state
+# use RUNTIME_PM_ENABLE/DISABLE instead.
+# Separate multiple addresses with spaces.
+# Use lspci to get the adresses (1st column).
+# Default: <none>
+
+#RUNTIME_PM_DENYLIST="11:22.3 44:55.6"
+
+# Exclude PCIe devices assigned to the listed drivers from Runtime PM.
+# Note: this preserves the kernel driver default, to force a certain state
+# use RUNTIME_PM_ENABLE/DISABLE instead.
+# Separate multiple drivers with spaces.
+# Default: "mei_me nouveau radeon xhci_hcd", use "" to disable completely.
+
+#RUNTIME_PM_DRIVER_DENYLIST="mei_me nouveau radeon xhci_hcd"
+
+# Permanently enable/disable Runtime PM for listed PCIe device addresses
+# (independent of the power source). This has priority over all preceding
+# Runtime PM settings. Separate multiple addresses with spaces.
+# Use lspci to get the adresses (1st column).
+# Default: <none>
+
+#RUNTIME_PM_ENABLE="11:22.3"
+#RUNTIME_PM_DISABLE="44:55.6"
+
+# Set to 0 to disable, 1 to enable USB autosuspend feature.
+# Default: 1
+
+#USB_AUTOSUSPEND=1
+
+# Exclude listed devices from USB autosuspend (separate with spaces).
+# Use lsusb to get the ids.
+# Note: input devices (usbhid) and libsane-supported scanners are excluded
+# automatically.
+# Default: <none>
+
+#USB_DENYLIST="1111:2222 3333:4444"
+
+# Exclude audio devices from USB autosuspend:
+#   0=do not exclude, 1=exclude.
+# Default: 1
+
+#USB_EXCLUDE_AUDIO=1
+
+# Exclude bluetooth devices from USB autosuspend:
+#   0=do not exclude, 1=exclude.
+# Default: 0
+
+#USB_EXCLUDE_BTUSB=0
+
+# Exclude phone devices from USB autosuspend:
+#   0=do not exclude, 1=exclude (enable charging).
+# Default: 0
+
+#USB_EXCLUDE_PHONE=0
+
+# Exclude printers from USB autosuspend:
+#   0=do not exclude, 1=exclude.
+# Default: 1
+
+#USB_EXCLUDE_PRINTER=1
+
+# Exclude WWAN devices from USB autosuspend:
+#   0=do not exclude, 1=exclude.
+# Default: 0
+
+#USB_EXCLUDE_WWAN=0
+
+# Allow USB autosuspend for listed devices even if already denylisted or
+# excluded above (separate with spaces). Use lsusb to get the ids.
+# Default: 0
+
+#USB_ALLOWLIST="1111:2222 3333:4444"
+
+# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
+# on system startup: 0=disable, 1=enable.
+# Note: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
+# are ignored when this is enabled.
+# Default: 0
+
+#RESTORE_DEVICE_STATE_ON_STARTUP=0
+
+# Radio devices to disable on startup: bluetooth, nfc, wifi, wwan.
+# Separate multiple devices with spaces.
+# Default: <none>
+
+#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth nfc wifi wwan"
+
+# Radio devices to enable on startup: bluetooth, nfc, wifi, wwan.
+# Separate multiple devices with spaces.
+# Default: <none>
+
+#DEVICES_TO_ENABLE_ON_STARTUP="wifi"
+
+# Radio devices to enable on AC: bluetooth, nfc, wifi, wwan.
+# Default: <none>
+
+#DEVICES_TO_ENABLE_ON_AC="bluetooth nfc wifi wwan"
+
+# Radio devices to disable on battery: bluetooth, nfc, wifi, wwan.
+# Default: <none>
+
+#DEVICES_TO_DISABLE_ON_BAT="bluetooth nfc wifi wwan"
+
+# Radio devices to disable on battery when not in use (not connected):
+#   bluetooth, nfc, wifi, wwan.
+# Default: <none>
+
+#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth nfc wifi wwan"
+
+# Battery Care -- Charge thresholds
+# Charging starts when the charger is connected and the charge level
+# is below the start threshold. Charging stops when the charge level
+# is above the stop threshold.
+# Required hardware: Lenovo ThinkPads and other laptop brands are driven
+#   via specific plugins:
+# - Use the tlp-stat -b command to see if a plugin for your hardware is
+#   active and to look up vendor-specific threshold values. Some
+#   laptops support only 1 (on)/0 (off) instead of a percentage level.
+# - If your hardware supports a start *and* a stop threshold, you must
+#   specify both, otherwise TLP will refuse to apply the single threshold.
+# - If your hardware supports only a stop threshold, set the start
+#   value to 0.
+# - The names of the batteries shown by tlp-stat -b don't have to match
+#   the _BAT0 or _BAT1 parameter qualifiers. Please refer to [2]
+#   to see which qualifier applies to which battery.
+# For further explanation and all vendor specific details refer to
+# [1] https://linrunner.de/tlp/settings/battery.html
+# [2] https://linrunner.de/tlp/settings/bc-vendors.html
+
+# BAT0: Main battery
+# Default: <none>
+
+# Battery charge level below which charging will begin.
+#START_CHARGE_THRESH_BAT0=75
+# Battery charge level above which charging will stop.
+#STOP_CHARGE_THRESH_BAT0=80
+
+# BAT1: Secondary battery (primary on some laptops)
+# Default: <none>
+
+# Battery charge level below which charging will begin.
+#START_CHARGE_THRESH_BAT1=75
+# Battery charge level above which charging will stop.
+#STOP_CHARGE_THRESH_BAT1=80
+
+# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable.
+# Default: 0
+
+#RESTORE_THRESHOLDS_ON_BAT=1
+
+# ----------------------------------------------------------------------------
+# tlp-rdw - Radio Device Wizard
+# Note: requires installation of the optional package tlp-rdw.
+
+# Possible devices: bluetooth, wifi, wwan.
+# Separate multiple radio devices with spaces.
+# Default: <none> (for all parameters below)
+
+# Radio devices to disable on connect.
+
+#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
+#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
+#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"
+
+# Radio devices to enable on disconnect.
+
+#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
+#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
+#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
+
+# Radio devices to enable/disable when docked.
+# Note: not all docks can be recognized, especially USB-C docks. If a LAN
+# cable is connected to the dock, use DEVICES_TO_DISABLE_ON_LAN_CONNECT
+# and DEVICES_TO_ENABLE_ON_LAN_DISCONNECT instead.
+
+#DEVICES_TO_ENABLE_ON_DOCK=""
+#DEVICES_TO_DISABLE_ON_DOCK=""
+
+# Radio devices to enable/disable when undocked.
+
+#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
+#DEVICES_TO_DISABLE_ON_UNDOCK=""